The command s snake using cell s as the image shows, are the type of batteries that CR32 can find the representative of the alarm, a distributor or store any type watchmaker or photographs.
By opening up your cobra command to check the mounting position of the stack because the polarity must be maintained, otherwise your command will never work.
If you do not remember the position to consult the previous post on the control box snake and click the picture in order to visualize the proper mounting position of the stack.
After re-assembling your command to check its proper functioning, sometimes this is where the difficulties begin, it happens that the controls no longer work and the need to program the command, this is not necessary to use the services of technical or snake even to some reseller.
To schedule your command snake just follow the procedures that I describe here:
1. I stepped from the vehicle to which it is associated with your command alarm.
2. Press the two buttons simultaneously control the alarm, LED command should be flashing.
3. Keep both buttons pressed until the led on the delete command, release the buttons of the command and verify that the LED is fixed.
4. Press the button twice and the higher the car alarm will trigger.
5. Repeat the process if no results, because sometimes some of the procedures were not properly carried out and the alarm did not recognize the command.
And voila, after the command is not damaged and we have to think about buying a new one, I know some of you might be thinking that after all is so simple and the command in a drawer waiting for an opportunity to return to work.
I know from experience that this happens a lot, I command you plan to charge that much was saved and that only after losing the second is the re-run.
I hope this post about changing batteries and reprogramming of the control will facilitate the users who may have this problem here and that can access the correct procedures for this simple operation.
See video on how to put the command alarm back in operation.
Also read these articles:
51 Comments on "Changing the battery and program the command"
Dear friend I give you my congratulations for the information and solutions presented.
I wanted to ask for help because of my alarm, I ended up replacing the batteries closer to a watchmaker and now my remote does not work he sends signal but does not open or close the car and not the alarm works. What should I do? But I tried to get in various shops alarm zone Vila Real etc or make a copy if possible and nobody solves the problem. Takes a lot of control and I have done everything to fix it and nothing. I leave my email here (removed) if I want to help or even enter a store that I solve the problem.
Very grateful for your help in solving this problem.
Sincerely: Jose Rodrigues
Thanks for the comment.
If the command is the round just follow the directions of the post, replace the batteries and program the command.
Sometimes it works at first, make sure the light illuminates the command and repeat the process.
hello, good afternoon Mr. Jose Rodrigues.
Spend a store network chaviarte and find there for sure, I know a friend of mine bought one in store dolce vita port. respects
Already works?
As I said earlier in 99% of cases is not necessary to buy a new command, just reprogram it when replacing batteries.
hello and how qo reprograms??
ja agr and buying a new QSO encodes how?
respects
To reschedule or do a reset command crashed when replacing the battery just follow the instructions of the above post.
To synchronize a new command wait for the post concerned (which is in the pipeline).
hello, good morning. ms If I have only one command and buy another as the program??
thank you
cumpa
I tanh a new alarm ... it came with a card with some numbers ... these numbers serve to activate or deactivate the alarm is not it? But what's the procedure?
Thanks for visiting Nelio.
If the alarm is new, besides the card with the code of decommissioning, it also should have been delivered where the user's manual explains the entire process.
To be exact I need to know what type of alarm, because if it is a new model the procedure differs from earlier models in which the code was inserted through the ignition switch, new ones are through the LED.
Say which model.
Hola, thank you for the tip. He was fumbling with this hassle of re-programming of the alarm and was beautifully resolved. I am grateful! Adriana
Hello ... I think the model is the G100 at least that's what is written in the manual ... yes they gave me the manual I've been reading but I could not know what he wanted ... the alarm has the modules for the glasses too ... alarm has led you as you said yourself with red light and a button, I know you have to press the button for the alarm dessativar but I'm not even anything to do ... as the card has written the PIN CODE 9736
Another thing ... esprementei to take out the battery and return to the command to see if a program was needed but was not ... that these new alarms will no longer need?
To deactivate the alarm in case of failure of command clicking (in your case) 9 times the button the LED, the LED flashes once, clicks 7 times, the LED flashes once, clicks 3 times, the LED flashes back to a time and finally six times and the alarm turns off.
Try to turn the alarm off with the command and through this process.
Tell me if it worked.
I did like teaching here to adjust the volume, but not led, I followed all the steps and nothing.
Another thing came charges that certain alarms each time you turn on or off the alarm he makes a whistle or two depending on whether or disabling this but my call does not make it ... how can I do? already read the manual several times but does not explain how.
Hug Nelio
The process is the same that you use to adjust the volume.
Often it is not possible to enter the programming mode due to bad connection of the alarm.
The switch wire doors and hood must be connected.
Thank leaving comments on their articles, it becomes easier for everyone.
WHERE TO BUY AN ALARM COBRA CHEAP? WHICH MODEL TO COUNSELING?
Thank you for acknowledging me in capabilities on the field for advice, but can not do it without indicating which model of vehicle in which to install alarm cobra.
I will be glad to help if I indicate the make, model and year of car.
Good friend.
I hereby ask for your help. My car (Opel Corsa) left the factory with a Cobra 5801 alarm, but as ocarro bought second hand commands did not exist. As such I wonder if it is possible to control the alarm and universal commands like me would be possible to program the commands to the alarm since I have absolutely no data regarding the alarm unless the reference and model.
Greetings and thanks.
Tiago Teixeira.
Dear James
You can ask the representative encoding new commands , if it has no reference to the alarm codes will have to disassemble the plant and send to technical services.
Boas,
I have a problem with my alarm, I was gone 10 days and when I turn flashes 5 times (instead of two), when I disconnect flashes four instead of one. The clock, interior light and radio do not work. What could it be?
Boas,
I think the reason the clock, interior light and radio not working due to a blown fuse, to resolve the addresses of alarme.Pode probably be related to the inner light or the car battery ran out.
Check fuses and test the alarm .
Check back often if you need help.
Cumps
Just want to thank you very much for the information provided here! Saved me from having to take the car to beep for a workshop to get dismantled the alarm and send commands over the keys to Lisbon and etc etc..!
So simple!
Awesome right!
Thank you once again!
Without more and best regards
Cheers
Thanks for stopping by and comment.
It's always nice to know that our work has helped someone.
Come back.
Cumps
good night!
I bought a new Cobra alarm, model G100 or G300 did not know for sure, I know I have pin code, not the siren keeps itself going round and has commands that happens ... one of them ran out of battery and was mto time without the battery attached, deprogram now, it happens that I've tried to follow the steps listed on the site, open the bonnet, door etc. .. but it does not fix or not the LED flashes the hazard lights ... does nothing ... that is, it seems that there is connectivity between the car and the command ..
respects
Carlos Carvalho
Good evening,
For models which refers simply press the button for some time with the car.
Cumps
Good evening,
I mod.5340 snake alarm after replacing the batteries stopped working.
Thank you. a tip for the program.
Thanks
Good afternoon,
I believe it refers to commands from the oldest, with two square buttons, all right?
If so check the battery contacts, clean the area of the buttons with alcohol and retest, this kind of commands do not need programming.
Cumps.
ok.os au these commands are so many attempts in this genre acavarao come apart at Ebey bought one and I can not foncionar thanked for the tip if possible ob,
These commands have the same type of programming of the new, ask for a copy is required paragraph who is a sticker inside the command, if there is no need to disassemble the plant and sends it to the technical services to new commands.
I do not think there is another way, dismantle the plant and send it together with this command, there may be a reschedule.
Cumps
I have a cobra alarm 1994 ... the alarm works connected with the key but I can not configure a command ... How is it done?
Their alarm has yet commands rectangular with two green buttons?
If this is the case these commands do not have programming, open the box, replace the battery if it is unloaded and wipe with alcohol (without exaggeration) the area where the printed circuit board push buttons.
Cumps
Good.
I needed to replace the old battery from the 7777 command of Cobra. Initially I followed the instructions in the manual but the command simply failed to act (led lights up but the command center of the vehicle does not respond). I searched the net and found your blog on the subject and followed your directions but still the problem of non-operation the sistema.Aparentemente not get past Phase 2 - corresponding to the second paragraph of his text on the programming of the command - which light the LED command is fixed and not blinking when in simultaneous keystrokes.
Thank you for your attention.
Cumps,
Joao Gomes
Boas,
You must perform the procedures in the car, pressing both buttons simultaneously for some time (delay) to change state and then press the big button of the command.
If the LED lights of the command, the procedure is a behind descrito.Tente again.
Respects
Hello,
In a few days now that the command does not work correctly. When you press the button to open the door the led is fixed for a few seconds and does not open the car, then flashes a few times and hangs up.
When I try again, or goes well and the car or open the problem repeats itself.
What is the problem, lack of battery?!
It is most likely.
Replace battery and reprogram command.
I changed the battery in the alarm Sicurtronic command (command with only one button) and do not know how to reprogram it. Since I think the manufacturer is the same Bosch might get help.
thanks
The model then relates to what is equal to the Cobra with a slightly different design and therefore the procedures are the same.
The models with only one button Sicurtronic were represented by Bosch in Portugal until a few years now disappeared from the market altogether, I do not know if I have anything saved to help with that, but on Monday I can search and post here.
Cumps
good night ... already searched for a solution to ca a situation that does not taste great, nor do I know if you have a solution ... I bought a used car, peugeot 106xsi 95, wore a cobra alarm 7915 ... normally works ok, but not like the block ... .. engine type, turn off the car, after 20-30 seconds is not caught, blocks the injection pump ... ... to do so to take this situation??
lengths and thanks ...
I appreciate help for the Post of February 27. Alarm Sicurtronic.
Bound
Good evening,
The command that has no regards programming, today I could not, but I'll try to speak with a company that made the technical assistance of Bosch / sicurtronic, may still be able to repair this command / control panel.
Cumps
Thank you for your attention
Cumps
Good evening,
Today I spoke with who was assisting sicutronic alarms, as I said this command has no programming and no longer exists any material for repair, he himself had bought the entire stock of several repairmen and sold it several months ago.
If the command only has crashed after changing the battery is not likely to be damaged, I know that maybe it did but make sure the battery is indeed good (already happened and new and unfilled), it is in position correct, clean the contacts, check the welds of the board and try to work without the box.
I believe that if not one of these things will do nothing, I regret not being able to help more.
Cumps
Good afternoon
I come to ask you please if possible give me a little help on a problem that I came in alarm cobra.
When I turn on the lede does not flash, is fixed, and you hear a little whistle from the area of the engine (when you plumb the league and appears momentarily). I suppose the alarm will be self-powered
Sound is weak and this lack of power in the battery of the same alarm ...
Really? He asked the favor to those who know the subject if I confirmed.
Grateful in advance for your attention.
ASRosa
Good afternoon,
I do not think the problem is that, the alarm turns on and closes the doors?
What is the type of alarm, car?
Cumps
Good night
The manual alarm does not indicate clearly what it is. Has a list 7901-7919. I have to see the car if I find the template. The remote is a 7777 which I think says little.
However, the command opens and closes doors, but when he closed the light blinks twice and do not do as usual, ie the LED was blinking but stays fixed and there is the buzzer to call but still.
Thanks anyway.
Respects
ASRosa
Check the switch hood or any door that is not closed properly.
Cumps
This topic saved me a trip to the workshop and an expense that would certainly not small. Thank you.
Good ... Sicurtronic have an alarm installed in my car and just have a command to run.
Does anyone know of any representative or where I can send more commands to do?
Thanks to all and cumps
Depends on the model of the command, for the oldest commands no longer exist but for the latest models can be used in the 7777 Cobra.
If sending image can answer with more certainty.
Cumps
admin ... like sending the picture?
Sent mail
Comments