Google Buzz

For the command 's original car, besides opening and closing doors also activate the alarm, you must perform a self-learning of the activation signal / desactivação.Embora this is an operation usually performed only once (when mounting alarm), it is possible that factors such as changing the car battery or any other can prevent the original commands of your vehicle to work properly.

Before describing the steps required is reprogramming the original commands, I draw attention to the fact that you can only achieve this if the alarm is properly connected, including the wire connection to the hood and door switches.

Entry into programming and self-learning of key command

The following conditions are necessary to memorize (or rememorizar) commands to the original distance of the vehicle:

-Alarm system off.
-Door and hood open.
Ignition-on (without engine running).

Sign in programming:

-Enter your pin code , you can see how to enter the code here .
If all conditions are complied with the LED lights up and after about 3 sec the system will respond with a signal of the direction indicators (blinkers), noting that in programming.

-Disconnect and reconnect the ignition.
The direction indicators will flash twice to confirm that it is in the function table base alarm system.

-Press the LED inside to activate the self-learning.
A long blink the LED confirms the activation.

-Close the door and turn the ignition.
The LED will blink rapidly to indicate that it is ready to receive the activation signal.

-Press the closing doors of the original query so that they are close.
The LED lights steadily during 2sec confirming that learning took place this sign.
Then a slow blinking indicates that the system is again ready to save the sign of deactivation.

Push-button door opening of your original remote.
The LED will turn off the alarm and a flashing of the direction indicators confirm that the operation was successful.

Test your command of key documents confirming the opening / closing and simultaneous on / off the alarm.

These steps are only valid for alarms Cobra 3868 and should only be made in case of malfunction of the original commands in relation to the alarm, not the closing of doors, in this case should be checked by the dealer concerned.

Until the next tip.

Blog Widget by LinkWithin
Liked this article? Share it please!:
  • Digg
  • del.icio.us
  • Facebook
  • NewsVine
  • Reddit
  • StumbleUpon
  • YahooMyWeb
  • Google Bookmarks
  • Yahoo! Buzz
  • Live
  • LinkedIn
  • MySpace
  • Posterous
  • Twitter
  • Add to favorites
  • PDF
  • Print
  • Rec6

Also read these articles:

  • No related articles

11 Comments on "self-learning command-unique"

Subscribe to this Article Comments Feeds or leave trackback
Carlos says in January 17th 2010 at 24:36 pm

How many times do I have to press the LED button to enter the self learning?

Admin January 17th 2010 at 1:56 pm

After entering the pin, turn the ignition off and have to press the button once the LED.

Carlos says in January 19th 2010 at 11:39 am

Ok ... You are working properly, although it still seems a bit rogue to disarm when the doors open for only the 2nd attempt is disarming. But everything else works, bonnet, glass intrusion in the cabin, everything is ok!

Thanks

Olive says in January 28th 2010 at 12:47 am

Good I need help with an alarm that crashed, or better weapon and disarms but often sozinhoe lock the doors and get the blinkers flashing and the car will not start, it's a bmw 325tds and I have the instructions in the module alarm has the following instructions.

4M1980STA - 0.9800181 and the other module has 4M055STA-0.9700503

I wonder if it is possible to find manual or how to solve the problem.

Thanks
Rui Oliveira

admin January 28th 2010 at 8:54 pm

Boas,
In what year is your car?

Junior Carlos says in April 9th 2010 at 2:17 am

Good night.
I have a fiat with original factory alarm, I lost the remote control (command) of the alarm and managed to buy another one exactly like the previous one, which in turn does not work.
I wonder if anyone knows any place in Rio de Janeiro that encodes the control for it to be Paired with the car alarm?
Who does this kind of service and that name is given to this kind of service?
My alarm is a HL Original Fiat, and the new control box has information HL-6664 is rectangular with a red LED and a button.
Thanks

admin April 9th 2010 at 7:54 pm

Usually the original commands only his own dealership is that you can configure.

rodrigo says in April 14th 2010 at 1:57 pm

good, got a Corsa B with cobra alarm, the battery in my command was to be replaced and now does not work, how can I solve this problem?

admin April 14th 2010 at 8:55 pm

Follow the instructions in the article replace the battery and programming command .
Cumps

rodrigo says in April 20th 2010 at 6:48 pm

thanks for the help.
already got my operational command, and with 30 euros which would pay to memorize the command when I go to dinner with "maria".
once again ... gracias ...

admin April 20th 2010 at 7:19 pm

Glad it works.
Now 30 euros for something that is done in two minutes ... ... ... ... ... ... ... no coments.
Cumps

Comments